Advanced Imaging

AdvancedImagingPro.com

   

Advanced Imaging Magazine

Updated: January 12th, 2011 09:49 AM CDT

Architecture for Airborne Applications

Processors for Airborne Intelligence, Reconnaissance, and Surveillance
Images courtesy SRC Computers
Figure 1: In the Implicit+Explicit Architecture, Dense Logic Devices (DLDs) encompass a family of components that includes microprocessors, digital signal processors, as well as some ASICs. These processing elements are all implicitly controlled and typically are made up of fixed logic that is not altered by the user.
Figure 2: Systems can be built with a single MAP processor and microprocessor combination, or when more flexibility is desired, Multi-Ported Common Memory accommodating up to three MAP processors and Hi-Bar switches accommodating thousands of MAP processors can be employed.
Figure 3: SRC servers that use the Hi-Bar crossbar switch interconnect can incorporate common memory nodes in addition to microprocessor and MAP nodes. Each of these common memory nodes contains an intelligent DMA controller and up to 16 GBs of DDR-2 SDRAM.
Figure 4: The MAP processor used in this system was the most powerful SRC-6 MAP processor ever produced. It was coupled to an Intel Pentium microprocessor and used a Fedora Linux operating system.
Figure 5: The second airborne system in production is a 10-module system designed for payload bay 3 of the General Atomics Sky Warrior, but is also usable in other larger manned and unmanned platforms. It contains a dual Xeon motherboard, a Hi-Bar switch, 750 Gbytes of removable encrypted storage, 28 VDC power system, thermal solution and a mixture of up to 10 MAP processors or common memory modules.
Figure 6: This system is being designed to withstand an operating range from –50C to +50C, an altitude limit in excess of 25,000 feet. and will meet shock and vibration requirements for single engine aircraft weighing less than 12,500 pounds.
Figure 7: A grayscale pixel’s intensity is simply the pixel’s eight-bit numeric value, but the intensity information is distributed among the individual RGB values for a color pixel. To obtain the intensity value for an RGB pixel, each 24 bit RGB value is transformed from the RGB color space to the Hue-Saturation-Intensity (HSI) color space. The intensity values for all pixels in both frames are then histogrammed. From these two intensity histograms, a statistical Cumulative Distribution Function (CDF) is created and then normalized for each frame. A mapping function is created from these two normalized CDF arrays to map the original color pixel intensity values to a new intensity value such that the new intensity value distribution matches the GS pixel intensity value distribution. The original intensity values are re-mapped and the new HSI image is transformed back into the RGB color space.
Figure 8: The MAP processor’s GCM Bank 0 acts as a frame buffer for the RGB image and GCM Bank 1 acts as a frame buffer for the GS image. In stage 0, two RGB and six GS pixel intensities are histogrammed in parallel every clock. The integer RGB intensity calculation is part of the RGB histogramming pipeline. After all pixel intensities for both frames are histogrammed, stage 1 calculates the CDF arrays for both histograms for all histogram bins in parallel. Stage 2 normalizes both CDF arrays in parallel, a single precision floating point (SPFP) calculation. Stage 3 uses both normalized CDF arrays to generate the histogram matching MAP array. Finally, stage 4 re-reads the RGB image data two RGB pixels per clock from GCM Bank 0 and calculates the HSI pixel values. The two integer intensity values select two new intensity values from the Map array (generated in stage 3). The two new intensity values are cast to SPFP, and together with the two SPFP pixel hue and saturation values, are converted back to the 24 bpp RGB color space and stored in GCM Bank 1.
Figure 9: The CPU normalized cross-correlation application is a single threaded, serial implementation of the algorithm shown in Figure 8.
Advertisement

By David B. Pointer
SRC Computers

The initial implementation on a SRC-7 Series H MAP processor used only one User Logic Chip. This implementation uses a major performance enhancement by summing the contribution of four swaths at a time into every voxel in the 2D image. We implemented a two-chip version that sums the contribution of twelve swaths into each voxel in the 2D image.

Optical Sensor Image Processing

Three optical image processing applications on the SRC-7 Series H MAP processor are presented in this section: image fusion (combining multispectral sensor data for image enhancement), feature tracking (tracking objects of interest across frames), and cross-correlation (identifying objects of interest). The details of each application are described and the measured performance of each implementation on a microprocessor and the MAP processor are presented.

The COTS CPU board used for performance measurement contains dual 3.0 GHz Intel Xeon CPUs (2048 KB cache) and 2 gigabytes of system memory. The SRC-7 Series H MAP processor contains dual 150 MHz Altera® 2S180 FPGAs with 64 megabytes of on-board memory (OBM) and 2 gigabytes of Global Common Memory (GCM). Input frame data rates are at the full cameralink bandwidth of 900 megabytes per second.

Six optical image sensor geometries from 1.9 megapixels to 112 megapixels, are used for each implementation’s performance measurement.

Image Fusion

Multispectral data fusion applications combine spatial and spectral data obtained from different sensors into a single image to reveal information otherwise unavailable from a single sensor. For example, the fusion of two bands of infrared (IR) sensor data can distinguish large warm objects from small hot objects while a single band IR sensor cannot. Another example is the fusion of SAR sensor data with optical sensor data. SAR sensors provide spatial information about an object while optical sensors provide spectral information. The combination of spatial and spectral data enables object classification and identification.



Subscribe to our RSS Feeds